Flexiteek is a synthetic teak panel and it is made of composite materials, 100% recyclable to other products and its non–slip quality is superb and nobody yet on first viewing or touching think it is anything other than real teak. The deck will not fade, dry out, split or crack and requires minimal maintenance.

How do you clean a flexiteek deck?

STAIN/SPILL REMOVAL Flexiteek is stain resistant and most spills will clean up with warm soapy water (for rapid stain removal, clean while stain is fresh). We recommend the use of a Flexiteek Cleaner; simply spray the Cleaner on the area, scrub with a white 3M doodle bug scrubber and rinse with water.

Innholdsfortegnelse

What is a good substitute for teak on a boat?

In many parts of a yacht, teak has been replaced by mahogany and Iroko (also known as ‘African Teak’, although each wood has nothing in common) but it remains the material of choice for decking.

Where is flexiteek made?

Flexiteek products are manufactured in the UK and Sweden.

What is flexiteek made of? – Related Questions

Can you sand flexiteek?

Can you re-sand it? Flexiteek 2G can be re-sanded by hand using 40 to 80 grit sanding paper and working in the direction of the grain. The rougher the sandpaper, the deeper the grain will be.

Can you sand synthetic teak?

Sanding synthetic teak flooring

For bad scuffs or small burns such as those caused by a cigarette, or a stubborn stain that has been left to dry, the deck can be lightly sanded by hand with 40 grit sandpaper. This is also effective treatment when an area has worn smooth.

How do you clean fake teak?

Synthetic teak decking is stain resistant and most spills will clean up with warm soapy water (for rapid stain removal, clean while stain is fresh).

How do you clean flex teak?

Use warm water with soap associate with regular brush (along PVC fiber grain) will clean off stains, spots on flexiteek surface, otherwise, acetone, sand paper will be applied to clean off those deep spots..

How do you install faux teak decking?

Is it OK to sand teak wood?

Teak is one of the softer of the hardwoods, so it is easy to quickly sand away a lot of teak when too aggressive. So, start with 80 Grit and lightly sand. Adjust pressure, speed, or sanding grit to refine the rate of removal. ALWAYS keep the sander moving over the surface.

Can you sand down teak furniture?

Lightly sanding teak wood will reveal a fresh and glowing finish below the surface level. This will restore the original honey brown glow. Sanding can be a bit more difficult on furniture that has hard to reach areas so you have to work around these spots by hand.

Can you use an orbital sander on teak?

Step 2: Put fresh pads on the orbital sander; don a dust mask, gloves and eyewear; and start sanding. The orbital sander is designed to move back and forth in a pattern that doesn’t leave discernible marks on the underlying wood. Let the tool do the work; avoid pushing down too hard on the sander.

How do you sand and polish teak?

Sand the teakwood to remove the gray-colored surface grain.
Switch to a fine, 220-grit sandpaper or foam sanding block, and continue to sand the entire teakwood item to smooth down rough grain and provide a satiny smooth finish.
Remove sanding dust by wiping the teakwood down with a tack cloth.

How do you make teak look new again?

How do you bring teak back to life?

How to Revive a Teak Wood Finish

Clean the Teak. Wash the teak with an all-purpose cleaner to remove surface grime and dirt, instructs Practical Sailor.
Scour the Wood. Scour the wood with a gentle cleanser.
Rinse the Wood.
Remove Deep Stains.
Sand the Wood.
Apply Teak Oil.
Apply Varnish for Protection.

Can you clean teak with vinegar?

Using a teak cleaner or a homemade solution of vinegar and warm water (1 cup vinegar to 4L of water), evenly wash down the surface with a soft cloth. Let the vinegar solution soak into the teak for about 15 minutes before cleaning it with a sponge in line with the timber grain.

Can Murphy’s oil soap be used on teak?

Then a coat or two of Teak oil and you are good to go. For products that don’t require sanding, or you don’t want to sand them, but are just dirty give Murphy’s Oil Soap a try and that should clean those products right up.